What Are the Most Common Garage Door Repairs?

0
310

A garage door is made up of many sections. Depending on the style of the door and its condition, the components might range from $5 to $200. Garage doors commonly include brackets, wires, sensors, rollers, and chains. New tracks and springs can run up to $200. Other parts that can be costly include Photo-eye sensors and broken cables. Learn about the most common repairs before you call a professional.

Torsion springs

If you notice that the torsion spring is wearing out, it is time to replace it. A broken spring can cause significant damage to your property and can even be dangerous. If your spring is weak, your garage door may slam down unexpectedly. If you notice signs of spring wear, it is best to contact a repair technician right away. Torsion springs are the most common garage door repair denton tx and you should know what to look for to make sure you have a safe and functional garage.

You need to measure the spring’s inside diameter and wire size. Next, measure the length and width of the spring, but you should remove the bracket, cables, and drums to do this. Next, measure each coil and convert the measurement into decimal. If the springs are too short, you can add another wiring layer and replace the old one. Remember to leave the coils unwound when replacing the spring.

Extension springs

The most common garage door repair is extension spring replacement. Despite their durability, extension springs can stretch and lose lift as they wear. The spring may need to be replaced to provide the same lift as the new one depending on the door height. In addition, your door may be opening unevenly, or the rollers may be coming out of the tracks. It can be a frustrating experience. Fortunately, there are a few ways to diagnose spring failure.

Extension springs are usually located above the upper horizontal tracks to provide a counterbalance to the door’s weight. As the force applied to the door increases, the extension spring expands to balance it. All extension springs should have safety cables attached to prevent the spring from becoming a projectile. Failure of the spring, cable, or bottom bracket may cause the door to bind or fall. Fortunately, most of these problems are minor.

Photo-eye sensors

One of the most common garage door repairs is a malfunctioning photo-eye sensor. If the photo-eye does not work, it has been bumped or has gotten dirty. To fix this problem, try adjusting the sensor’s position. For example, it should be adjusted to face opposite directions without disturbing the door’s frame. If the problem continues, try replacing the photo-eye sensor.

These devices send signals to the opener to determine whether or not it’s open. Unfortunately, when the photo-eyes are out of alignment, the door won’t open. To fix this issue, you must first remove the obstruction. For example, a small piece of dirt, cobweb, or the sun can obstruct the photo-eye sensor. Then, check for a broken bracket. If you find any of these problems, it’s time to contact a garage door repair specialist.

Broken cables

There are several reasons why cables break. In particular, the uneven tension can make cables slip out of the grooves and cause problems quickly. If the cables have slack, they may fall to the floor or become loose, resulting in the door’s unwrapping. If this happens to you, there are a few ways to prevent the problem from happening. 

Broken cables can also cause a garage door to become noisy and fall off the track. The problem can also result in an unevenly balanced door, which is frustrating and inconvenient. If you cannot fix the issue quickly, you may need to call a professional. 

Unplugged garage door motor

There are several reasons why a garage door could be stuck halfway between opening and closing. First, there’s probably a problem with the limit switch if this happens, which tells the garage door when to stop opening or closing. To fix the problem, adjust the limit switch. If this doesn’t fix the problem, you can try to lubricate the rollers. If lubrication doesn’t solve the problem, contact a professional to check the motor.

Another common issue is a faulty power source. The door may be plugged in, but the power source is not working properly. A faulty circuit breaker, GFCI outlet, or fuse could also cause the garage door to shut. Ensure the switch is plugged in and that lights are working in the garage. If you’re unsure what the problem is, you can try resetting the breaker on the wall or using the remote control.

Problems with the belt drive

There are two drive systems in garage doors: chain and belt. Although the chain drive is stronger, the belt drive is not as durable. It may only be able to lift moderately heavy items, but it will last longer. On the other hand, the chain drive is noisy. While this may not be a problem immediately, it can be a hassle over time. For example, if you notice a strange noise when your door is closed, it could be a belt drive problem.

Other types of problems with the belt drive for garage door repairs include a broken battery or a manual disconnect. The manual disconnect, usually a red release cord, should be free of obstructions. Clean photo-eye sensors and make sure they’re free of dirt and debris. Check that plugs are firmly pressed into outlets. Make sure the breaker has not tripped. Also, check that the wall button is secure and that there are no loose wires or tangled ones.